For those of us in the Northern Hemisphere, engine season is over once
again, but our friends on the ATIS internet mailing list from Australia and New Zealand are getting into the swing
of their season now, and a subject came up which affects many who transport their engines to and from shows.
* Just curious if anyone has any proven methods for loading and unloading engines from, say, a pick-up truck.
Brute force obviously works, but the wife won't want to be the provider of such force too often! Right now my Jaeger
is mounted on 3' long 4x4's. I might go ahead and pop for some wheels and make it mobile, but I'm not sure if I
should trust 2x6's to hold it rolling onto the bed.
As usual with such a practical query which is relevant to all makes of engine, this brought a good response.
* I have two 2"x12"x8' treated ramps that I keep in the back of my pickup. These work fine for my
engines. You could probably slide your engine on skids up the wide ramps, maybe with just a little help. There's
always help to be had at engine shows to take it out of the truck.
* A method I have used for loading/unloading an Atlas Diesel genset from a pickup is to use three long pieces of
2" steel pipe, using chain and making them into a tripod with one leg at the tailgate of the pickup and the
other two beside the truck just forward of the center of mass of the Atlas. Then, a hand come-along will lift the
engine, and the truck can drive forward away from it. By marking the spots for the legs, you can use the same system
for loading by first lifting the engine, then backing under it. This Atlas isn't that heavy, maybe 650lb.
* You mentioned concern over the strength of 2x6 ramps. If you provide some intermediate support for them, they
will be much safer.
* I use my forklift to load and unload engines.
* I have several methods. One is a engine hoist like you use for pulling engines from cars - with it and some lifting
straps I can pick an engine up out of the truck and set it on a low rolling cart or roll it in to the shop right
on the hoist. This is made easy by my concrete pad, driveway and basement shop. My other method is a pair of ramps
made of heavy 4 channel iron 7 long and a 12 volt winch in the front of the bed. These ramps work well with wheels
or skids, or engines with nothing under them.
For really heavy lifting I have an 8 I-Beam 20 long spanning the driveway into my basement garage with a 2 ton
chain hoist on rollers. I can lift the offending chunk and drive out from under it.
I have to work alone most of the time and have found that one must learn to think like an Egyptian in order to
move this stuff we all love!
* I decided a long time ago on channel iron - the wheels follow it like a set of rails, and I have to do all my
loading by myself.
When we had to load the vertical Famous at Portland we just tipped it over and rolled it up on the flywheels. I
used an engine hoist/crane at home to pick it up and drive off.
* The winch in the front of the pickup bed is the way to go. As for ramps, making them too strong is better than
an engine on your toe. Using a 2x6 alone might be a little weak. One set of our ramps is two lengths of 2 1/2"
steel angle (3/16") with a 2x6 bolted in between. They're awfully heavy - aluminum would lighten them up and
make them more manageable.
Whatever you do, figure out a way to secure them to your tailgate or pickup bed. Having the ramps slide out is
* Since your engine is on skids, you might want to make up a few dollys. Some lengths of 2" pipe might also
help. As you crest the top of the ramps, the skids will do a wheelie and will tip downward as the centre of gravity
comes over the top. The reverse happens when coming down, but as long as you know what to expect and plan accordingly,
the engines remain in one piece and you don't have to visit the doctor.
* You might be able to use my method. I got four wheel barrow wheels, made four axles 3/4 round x about 1 long.
Drilled four 3/4 holes in the skids of all my engines. When I go to shift the engine I jack one end of the skids,
fit the wheels and axles in to the holes drilled and repeat at the other end. Theres no steering but you can lever
it around with a bar easy eough. When the engine is put where you want it, take the wheels off and use them for
the next one you want to load up.
* If you watch garage sales you can pick up old skateboards for a couple of bucks. They have very tough wheels,
good bearings and a very tough laminated board on top that will move heavy loads easily. I use them when moving
stuff around the shop.
* Wheels work great on ramps. 2x6 is okay for smaller engines. You could screw/nail some edge guides for wheels
which would also help to stiffen planks. The aluminum plank ends that grip tail gate also are great. They sell
folding aluminum ramps, but these get pricey. I have seen small electric winches mounted in the front of body to
help load and unload.
Finally, on a totally different subject, its THAT time of year again, so heres a little cautionary tale which
appeared on the list recently:
I have a friend who owns, among other engines, a 5hp Hercules EK with the WICO PR mag. When he stored it last fall,
he let it drain (head too) until the water stopped flowing, than closed the brass cock again and replaced the pipe
plug in the head. Early this summer he pulled it out for a show and was horrified to find the lower part of the
cylinder water jacket split lengthwise. Further investigation revealed a blockage of debris in the water jacket
below the cylinder. Had he left the drain cock open, it might have eventually drained out anyway, but because he
closed it again he now has a freeze crack. I drained my Herc out at home after last weekend's show. The drain cock
remains open, and the pipe plug for the head is in my toolbox, just in case.
Credit for this article must go to Ted Brookover, who came to my rescue when my computer crashed, taking with it
the mail files where I had carefully stored this information - thanks, Ted!